Wild LT parts catalog
Every spare part for the Wild LT with its part number, what it does, and a direct link to Orbea's online shop where it's sold. Comparing full bike builds? Compare Wild LT models (M20, M10, M-Team…) →
- Parts
- 85
- In Orbea shop
- 67
- Groups
- 12
Headset & steerer
Bearing seals, compression ring, spacers, headset caps and the SIC manifold that routes cables through the headset.

Compression ring, fork crown race & bearing seal
The ZS56 crown race sits on the fork steerer and the ICR compression ring centres the upper bearing. Replace when the headset creaks, feels notchy or after swapping forks.

Headset spacer ring
Thin ring that sits between the upper headset bearing and the cable manifold to set the correct preload stack.

Headset cap HS02-A-01 (ICR)
Upper headset cover for bikes with internal cable routing through the headset (ICR). Seals the bearing and guides the cables into the frame.

HS02 split headset spacer kit
Aluminium split spacers (3× 10 mm, 1× 5 mm) that can be added or removed without disconnecting the cables — used to fine-tune bar height on ICR setups.

SIC HS02-05 manifold (OC stems)
Cable manifold that sits under OC Mountain Control stems and channels brake hoses and cables into the headset. Includes the full grommet set.

SIC HS02-06 universal manifold (aftermarket stems)
Universal version of the cable manifold for riders who fit a non-Orbea stem while keeping headset cable routing. Includes grommets.

SIC HS02 manifold grommet kit
Replacement grommets (L0–L3, R1–R3, R2e) that seal the cable entries on the SIC manifold — needed when you change the number of cables.

HS02 round headset spacer kit
Round 10 mm and 5 mm spacers that go above the stem to trim the steerer stack.

Headset cap HS02-A-18 (external routing, OC stems)
Headset cover for builds without internal headset routing, matched to OC Mountain Control stems.

Headset cap HS02-A-19 (external routing, standard stems)
Headset cover for builds without internal headset routing when using a standard 1-1/8" stem.
Stem & cockpit
OC Mountain Control stems, stem hardware and computer mounts.
Exploded views



OC ST-MC11 stem
Orbea's OC Mountain Control alloy stem (35–60 mm) with faceplate, steerer clamp limiter and top cap. Integrates with the SIC manifold.

OC stem bolt kit
Six M5×15 R8 tapered CrMo bolts for the faceplate and steerer clamp. Fits all OC stems except ST-RP21.

ST-MC10/20 top cap HS02-31
Top cap and M6×50 bolt used to preload the headset on OC Mountain Control stems.

OC CM-05 computer mount
Out-front mount that bolts to OC ST-MC stems. Includes adapters for Garmin, Sigma, Wahoo and Bryton computers.

OC CT-02 computer mount tray kit
Spare adapter trays (Garmin/Sigma, Wahoo, Bryton) and bolt for the CM-05 mount.

OC ST-MC20 stem
Orbea's OC Mountain Control MC20 stem (35, 40, 50 mm) with faceplate, steerer clamp limiter and top cap — the stock stem on many Wild LT builds.
Rear axle & hanger
UDH derailleur hanger, thru-axle and the rear axle bearings and hardware.
Exploded view


SRAM UDH X12 derailleur hanger (FS option)
Universal Derailleur Hanger with bolt and the black 30 mm full-suspension washer. Replace it if bent or if you run a non-Transmission derailleur.

Rear axle hardware kit
Chainstay-linkage insert, O-ring, circlip and 2.25 mm UDH spacer that complete the rear axle interface.

Rear axle bearing kit
Enduro Max 20307 and 6803 bearings for the rear axle pivot. Replace when the rear end feels rough or has play.

Rear thru-axle 12×184 mm, hollow
Hollow 12 mm thru-axle (1.0 × 15 mm thread) for the 184 mm SuperBoost-style rear spacing.

Rear axle cam (6 mm Allen)
Removable cam/lever head for the rear thru-axle, operated with a 6 mm Allen key.
Main pivot
Axle, bearings and seals for the main swingarm pivot.
Exploded view


Main pivot hardware kit
Main pivot axle and bearing spacer for the Wild 2027 frame.

Main pivot seal kit
Enduro SE 20×26×4 and 22×30×4 VG seals that keep water and grit out of the main pivot bearings.

Main pivot bearing kit
Two Enduro MAX BO 15×24×7 bearings for the main swingarm pivot.

Swingarm pinch bolt
M5×20 stainless bolt and washer that clamps the main pivot axle in place.
Linkage
Rocker links for Wild OMR (carbon) and Wild Hydro (aluminium) plus all linkage bearings, axles and seals.
Exploded views



Wild OMR 2027 29" linkage
Complete carbon-frame (OMR) rocker link for full 29" wheels, supplied with all 8 bearings installed.

Wild OMR 2027 27.5" (mullet) linkage
Complete carbon-frame (OMR) rocker link for the mullet setup (27.5" rear), supplied with bearings installed.

Linkage–frame bearing kit
Two 6805 (25×37×7) bearings for the link-to-frame pivot.

Linkage–shock bearing kit
Two 63801 (12×21×7) bearings for the link-to-shock trunnion pivot.

Linkage–frame hardware kit
Axle, bolt, spacers, O-rings and Enduro SE seals for the link-to-frame pivot.

OC FLP multitool MT-20
Hex 2/3/4/5 multitool that stores inside the linkage axle (FLP) — always on the bike for trailside fixes.

Linkage–shock trunnion hardware kit
Gold trunnion bolts, bolt rings, interior spacers and O-rings that mount the shock to the link.

Linkage–seatstay hardware kit (OMR)
Seatstay pivot axles and 10×13×2.5 mm washers for the carbon Wild OMR.

Linkage–seatstay bearing kit
Four Enduro Max 6800 (10×19×5) bearings for the seatstay-to-link pivots.

Linkage–frame seal kit
Two Enduro SE 28×37×4 VG seals that protect the link-to-frame bearings.

Wild Hydro 2027 29" linkage
Complete rocker link for the aluminium Wild Hydro with full 29" wheels, bearings installed.

Wild Hydro 2027 27.5" (mullet) linkage
Complete rocker link for the aluminium Wild Hydro in mullet configuration, bearings installed.

Linkage–seatstay hardware kit (Hydro)
Seatstay pivot axles, link spacer and 10×13×3 mm washers for the aluminium Wild Hydro.
Shock mount & flip chip
Geometry flip chip and the lower shock mounting hardware.
Exploded view


Flip chip kit
Drive- and non-drive-side flip chips with M8×48 bolt at the lower shock mount — switch between the high and low geometry positions.

Fox shock mounting hardware 31.75 × 8 mm
Aluminium reducer hardware for the lower shock eyelet. A Fox part — order it from a Fox dealer, not from Orbea.
Clamp, chain guide & bottle mount
Seatpost clamp, bottle holder and the upper chain guide.
Exploded view


34.9 mm seatpost clamp
Seatpost collar and bolt sized for the Wild's 34.9 mm seat tube.

Bottle holder bolts
Two M5×10 bolts and black washers for the bottle/accessory mount.

Bottle holder / range extender mount
Bottle holder that bolts to the frame mount. Orbea's shop lists the same part number as the RS 210 Wh range extender mount.

Upper chain guide
Upper chain guide with mount and bolts — keeps the chain on the chainring on rough descents.
Frame protection
Rubber chainstay, seatstay, downtube and motor protectors plus transparent frame protection kits.
Exploded views





Right chainstay rubber protector (Wild OMR)
Adhesive rubber chainslap protector for the drive-side chainstay of the carbon frame — keeps it quiet and protected.

Right seatstay rubber protector
Adhesive rubber protector on the drive-side seatstay, where the chain hits on big impacts.

Swingarm–frame rubber spoiler
Rubber spoiler that bridges the gap between swingarm and front triangle, keeping mud and stones away from the pivot area.

Downtube upper protector (800 Wh)
Upper rubber downtube armour for frames fitted with the FS800 battery.

Downtube upper protector (600 Wh)
Upper rubber downtube armour for frames fitted with the FS600 battery.

Downtube lower protector (800 Wh, OMR)
Lower downtube armour with bolts for carbon frames with the FS800 battery — takes rock strikes in front of the motor.

Downtube lower protector (600 Wh, OMR)
Lower downtube armour with bolts for carbon frames with the FS600 battery.

Motor protector / skid plate
Bolt-on protector that covers the Avinox drive unit. Available in S/M and L/XL variants — pick the one matching your frame size.

Right chainstay rubber protector (Wild Hydro)
Adhesive rubber chainslap protector for the drive-side chainstay of the aluminium Wild Hydro.

Downtube lower protector (800 Wh, Hydro)
Lower downtube armour with bolts for the aluminium Wild Hydro with the FS800 battery.

Transparent frame protection kit (Wild OMR 2027)
Complete 11-piece clear adhesive film kit for the carbon frame, in matt or gloss. Not currently listed in Orbea's online shop.

Transparent frame protection kit (Wild Hydro)
Clear adhesive film kit for the aluminium Wild Hydro, in matt or gloss.
Motor & battery mounting
Wild-specific motor fixing bolts and battery fixing kits.
Exploded views




Wild 2027 motor fixing kit
Front (77 mm) and rear (70 mm) M8×1.25 bolts, nuts and washers that hold the Avinox drive unit in the frame. The white dots on each pair of washers must face each other.

FS800 battery fixing kit
Wild-specific M5×11 and M5×28 TX20 battery bolts with square nut for the FS800 battery. Don't use generic Avinox battery bolts.

FS600 battery fixing kit (OMR)
Two Wild-specific M5×11 TX20 bolts for the FS600 battery on the carbon frame.
Cable routing & speed sensor
Cable Pass tubes, cable guides, grommets and Avinox speed sensor brackets.
Exploded views




Left Cable Pass tube + chainstay brake port
Internal cable tube and brake-hose exit port for the left chainstay (one unit) — cut to length when installing.

Right Cable Pass tube
Two internal tubes for the right chainstay that guide the derailleur cable/wire — cut to length.

Cable Pass frame–swingarm cable guide
Guide that routes cables cleanly from the front triangle into the swingarm.

Avinox speed sensor bracket (with ring)
13.75 mm sensor bracket for wheels using the external Avinox sensor ring on the brake rotor.

Avinox speed sensor bracket (built-in rotor)
15 mm sensor bracket for rotors with the sensor target built into the disc.

Head tube cable guide kit
Blind stops and internal/external cable guides for every head-tube routing configuration.

Shock cable grommets
Blind grommet for mechanical shocks and a grommet with a hole for electronic shocks.
Orbea RS controls
Orbea's own HMI switch units and wiring for the Avinox system.

Y cable: display – HMI switch – front light
Splits the display connection to feed both the Orbea RS HMI switch unit and the front light.

Orbea RS HMI control switch unit
Orbea's left-hand remote for Avinox: change assist mode/level, Walk and Boost, front light and power off.

Orbea RS HMI control switch unit with e-dropper lever
As the RS HMI unit, plus a lever (button E) that operates the OC DP-MC10-RS electronic dropper post.

E-dropper & rear derailleur harness
Connection harness that powers the DP-MC10-RS dropper and the SRAM AXS derailleur from the Avinox drive unit.
Avinox e-bike system
DJI Avinox drive units, batteries, chargers, displays, controllers and cables used on the Wild LT.

Avinox M2 drive unit
Mid-drive motor: 110 Nm, 250 W rated, ~2.65 kg, IP66, ISIS axle, EU 25 km/h / US Class 1. Replaced only through a warranty claim at an authorised dealer.

Avinox M2S drive unit
High-output version of the M2 (up to 150 Nm / 1500 W boost depending on battery). Replaced only through a warranty claim at an authorised dealer.

Charging port & battery–motor harness (Y cable)
Round charging port with cap and the 'Y' power cable that links the battery, the drive unit and the charge port. Bolts to the frame with 4 bolts.

Avinox FS600 battery
600 Wh internal battery (35.9 V, 16.7 Ah, ~2.87 kg). 0–80 % in ~1 h 42 min with the 508 W charger.

Avinox FS800 battery
800 Wh internal battery (35.9 V, 22.3 Ah, ~3.74 kg). 0–80 % in ~1 h 45 min with the 508 W charger.

Avinox 168 W charger (4 A, round port)
Compact 545 g charger. FS800: 0–80 % in ~4 h 54 min, full in ~6 h 11 min.

Avinox 508 W charger (12 A, round port)
Fast charger (985 g). FS800: 0–80 % in ~1 h 45 min, full in ~2 h 28 min.

Avinox speed sensor (650 mm)
Wheel speed sensor on the inner left dropout with internal cabling; reads Avinox 6-bolt rotors or the sensor ring.

Avinox speed sensor ring (42 teeth)
Toothed ring mounted with the brake rotor that the speed sensor reads.

Avinox DP100-F control display
2.0" 800-nit OLED display with 4G LTE, GNSS, 65 W USB-C output and connections for the HMI switch and front light. Firmware differs by region.

Avinox DPC100 control display
2.0" OLED display without 4G, with Apple Find My support and 10 W USB-C charging.

Avinox front light
Avinox headlight powered by the main battery; controlled from the display or HMI switch (low / high beam).

Avinox BC100 left wireless controller
Bluetooth remote (CR1620 battery, 22.2 mm clamp) for assist level, Boost and Walk. Used on Wild builds without the Orbea HMI unit.

Motor–display cable 900 mm
Main cable that connects the Avinox drive unit to the control display.
SRAM AXS – Avinox derailleur cable (780 mm)
HIGO Micro A cable that powers the SRAM Transmission derailleur from the Avinox battery and enables SmoothShift (shifting without pedalling).
No parts match your search.
Source: Orbea Blue Paper — Wild LT Carbon & Hydro 2027 (EN), spare parts and e-bike system sections. Part numbers, contents and product images © Orbea, reproduced for reference. Shop links checked November 2026. AvinoxLab is not affiliated with Orbea — always confirm compatibility with an Orbea dealer before ordering.